它幾乎是全斷面全土質的掘進機。它可以在N值從0-15的粘土，N值1-50的砂土以及N值10-50的卵礫石層等地層中使用，而且推進速度不會有太大的變化；⑵破碎粒徑大，其破碎粒徑可達掘進機直徑的40-45%之間；⑶施工精度高，施工后的偏差極小；⑷由于具有偏心運動，進土的間隙又比較小，即使用清水作為進水，也能保持挖掘面的穩定；⑸可以進行長距離頂進，也可用于曲率半徑比較小的曲線頂進；⑹施工速度快，每分鐘可進尺100-180mm之間；⑺機具結構緊湊、維修保養簡單、操作方便。無論在工作坑中安裝還是在接收井中拆除都很方便；泥水式推進工法適于頂進管徑規格為Φ600~3000mm。原材料及成品、半成品的質量必須合格，嚴格按國家規范和驗收標準進行檢驗。海滄區DN2800水泥頂管施工電話

頂管施工前，必須對施工現場或附近的地下管網進行勘測，對現場的供水、燃氣、通訊、電力等管線進行定位，對那些需要停工或遷離的管線進行嚴格分析，然后明確標出；第二要調查施工現場路面的車流、人流等交通狀況，必要時在路口設計交通引導牌，安排專人指揮，根據道路交通狀況合理安排施工路線；第三要對施工現場和附近的排水管道有清楚的了解，規劃設計更好的排水路線，必要時搭建臨時排水管道，防止施工污水流入其他位置。第四，如果施工現場有橋梁或其他建筑物，設計人員必須查明橋墩、橋臺基礎、建筑基樁等，以避免管道施工的破壞性影響。集美區DN3200球墨管頂管施工招標嚴格遵守“建筑工地安全生產六大紀律”，進入人員一律戴好安全帽。

施工測量注意事項（5）在工程銜接處，所設置的臨時水準點應相互測校調整，以防止差錯。（6）適當位置設置施工控制樁，控制樁應妥善保護。（7）測量時，應對儀器進行檢查調整，對原始記錄作詳細校對。四、頂管方案1、施工順序頂管施工前對頂管沿線進行調查，確定土壓平衡頂管施工工藝→頂力計算及后背墻設計→工作坑、工作井及接收井施工→施做基礎架設導軌/安裝后背墻→管道頂進施工，工作井、接收井施工、平面布置、井內布置及管內布置方案首先進行工作井與接收井的施工。工作井與接受井上層采用開挖法施工，下層在工作井和接受井四周打設鋼板樁后，周圍采用深井井點降水施工，根據實際情況每個工作井周圍需打四眼大口深井。大口深井井壁采用直徑400mm的無沙砼管護壁，井深25m,每個井中安裝一臺2寸深井潛水泵抽水，保證把水降至工作面以下500mm.

合同措施3.1根據當前實際情況，快速掌握材料質量、價格、供貨能力的信息、選擇好的供貨廠家，從而確保工程質量。材料訂貨時，要求廠家提供質量保證文件。材料訂貨、采購質量應滿足有關標準和設計要求，交貨期應滿足施工進度計劃要求。在訂貨時應依據質量標準簽訂合同。3.2與施工班組簽訂合同，實現一切管理基本原則，避免扯皮現象。在工程實施當中，合同是至高和比較終的，是所有班組行為準則的基礎，各班組碰到矛盾應無條件服從合同條款，以確保工程正常進行。廈門常達管業設置的臨時水準點應與沿線設置的水準點相校核至符合要求。

2.4對材料的采購、加工和運輸以及存儲建立管理制度，加快材料的周轉，減少材料的占用量，避免材料損失，變質、按質、按量、按期滿足工程需要。2.5原材料及成品、半成品的質量必須合格，嚴格按國家規范和驗收標準進行檢驗。對水泥。鋼筋、焊條等材料應有合格證，進場必須后取樣要復試，不合格材料不得用于工程上。2.6對于每道工序施工，都要進行技術交底工作，堅持“自檢”、“專檢”、“交接檢”三檢制度，堅持上道工序的施工質量達到合格標準，并及時上報監理，監理認定工序質量合格后，下道工序才能施工的原則。凡是在交接程序上出現了質量通病，項目經理必須對交接人員進行檢查，項目經理不追查責任的，公司將追查項目經理責任。車輛進出聽從現場指揮，粘土必須清潔后方可外運確保市容整潔。集美區DN2800非開挖頂管施工

廈門常達管業電工、電焊工、起重工等特殊工種作業人員必須經過專業培訓，持證上崗。海滄區DN2800水泥頂管施工電話

4.8操作人員應正確使用個人勞動保護用品，現場施工人員必須戴安全帽，并系好額帶，上下工作坑應走安全扶梯。4.9安全員每天做好施工現場巡視工作，發現問題及時制止糾正，重大安全隱患要下達整改通知單并報上級部門處理。4.10做好頂管工作坑周邊的環境保護工作，搞好文明施工，在基坑旁邊危房醒目位置設置安全警示牌。4.11電工、電焊工、起重工等特殊工種作業人員必須經過專業培訓，持證上崗。施工測量1、測量準備工作（1）進場后對甲方提供的測量控制點、水準點和標高進行現場復測，填妥《測量復核記錄》并簽字備案。（2）測量控制網的布設：根據甲方所提供的測量控制點及國家的有關規范和有關設計、施工規范的要求進行，以測量控制網作為該工程的平面、高程控制和施工測量放樣的首級控制及依據。（3）各種測量儀器、工具均應按有關的質量管理規定，在使用前送有關部門進行檢測，取得有關持檢部門的合格證書后才能使用。使用過程中有關人員應經常對所用的儀器、工具進行自檢、自校使之保持在良好的狀態中。海滄區DN2800水泥頂管施工電話

廈門常達管業有限公司擁有很好的服務與產品，不斷地受到新老用戶及業內人士的肯定和信任。我們公司是全網商盟認證會員，點擊頁面的商盟客服圖標，可以直接與我們客服人員對話，愿我們今后的合作愉快！

本文來自四川精碳偉業環保科技有限責任公司：//wasul.cn/Article/66f5099883.html